Kentucky No.1 concrete protective agent:
Kentucky No.1 concrete protective agent is a high performance external protective product for concrete surfaces It can enhance the hardness, wear resistance, and compactness of the concrete surface of structures such as bridges, roads, parking lots, floors, runways, and unloading pads, and extend the service life of concrete
Kantech 1The No. 1 concrete protective agent reports the third generation of concrete protection technology, which is made by refining various sites and surfaces at high temperatures through special rates and complex processes This product can Penetrate into the concrete and react with free calculus life to form an insoluble gel to seal the internal points of the concrete, so as to enhance the strength, surface hardness and overall compactness of the concrete, so that the concrete can resist the erosion from chemical products and mechanical wear and become more durable
This product is non-toxic, hazardous, non flammable, and does not contain VOC components It is safe and environmentally friendly to use
Kentek No.1 concrete protective agent can protect, hard, due proof, and seal the surface of concrete, improve its wear resistance, and extend its service life This product is widely used on the concrete surface of structures such as bridge decks, unloading platforms, lanes, runways, gas stations, and oil depots not suitable for policy concrete bricks or other policy materials with Established holes inside
Kentec No. 1 concrete protective agent Penerates into the concrete through effective penetration, reactions with free calcium lime in the concrete, forms gel in the concrete pores, reduces the concrete porosity, increases its compactness, and that improves the surface hardness and strength of concrete Allowing gas molecules to freely circulate while preventing external solid or liquid phases ses ants from entering the interval of concrete, allowing the concrete to still break
》》Main performance:
Kantech 1The use of No. 1 concrete protective agent on pores concrete through surface requirements2Spray coating construction, only required for use on mechanically pressed concrete surfaces1Spray coating construction, after spraying, it can be naturally driven(Please carefully read the construction plan before use)After using this product, the surface of mechanically pressed concrete will have a marble like cluster, and the longer it is used, the better the glossiness
》》Curing of new concrete surfaces:
After the end of light sharing(When the newly pooled floor is dry and hard to the point where people can walk on it without leaving footprints)Soak the concrete surface with this product as soon as possible to achieve a significant water retention effect This product can immediately react with the free calcium lime in the concrete to product gel to fill the internal pores, lock the water in the concrete, that significantly reduces the water vapor evaporation rate of the concrete Kentek concrete protective agent can be applied as a curing agent and surface strengthening agent to most concrete surfaces This product has a significant water retention effect on new ly maintained de concrete, but it has not been achievedASTM C-309Standards This product cannot be used on wet concrete surfaces!
》》Hardening, dust prevention, and sealing of concrete:
Different from other seals, Kentec No. 1 concrete protective agent products an insoluble gel through chemical reaction to wrap the calcium component in the solid concrete This product can improve the compactness and surface hardness of concrete, then make the concrete surface more wear resistance and corrosion resistance The gel produced by this chemical reaction can seal the pores inside the concrete, Signify icantly reducing the porosity of the concrete, preventing the liquid and solid inputs from internalizing, thus blocking the external pollutants, and keeping the treated concrete outline
》》Application scope:
Kentek No.1 concrete protective agent improves the surface hardness, wear resistance, immeasurability, due resistance, free how cycle resistance and other performance indicators of new and old concrete It is widely used in aerial runways, taxiways, parking lots, bridges, roads, loading and unloading aprons, Gas stations and other places This product can be Penetrated deeply into the interval R val of concrete, fully protecting the surface structure of concrete, and the effect is consolidated after using Kentucky No.1 concrete protective agent is a reactive site product that includes the relevant specifications for reactive sites used in bridge structures and decks in five states of the United States: Illinois, Ohio, West Virginia, Kentucky, and Virginia
》》Temperature conditions:
Newly made concrete surface: No need
Old concrete surface: Thoroughly clean the ground to ensure that the liquid can be Pentate Remove surface coatings, paint, other seals, and any other impacts that may affect the connection of American Kentucky No. 1 concrete into the interval Do not use acid to clean the concrete surface! Before using this product, ensure that the concrete surface is completely dry
》》Dosage:
The amount of mechanically polarized concrete surface is approximately 16-23 square meters per gallon, and the amount of brushed concrete surface is approximately 9-12 square meters The specific dose should be determined based on the population of the concrete and the temperature during construction For poles concrete surfaces, two coats of spray painting are required, while I mechanical finish of the concrete surface is sufficient once
》》Allocation requirements:
Kentucky concrete protective agent from the United States has been pre mixed before shipment and can be used directly (No need to allocate before construction use)
Tool cleaning: After using this product, immediately clean the spraying device with soap and water
Attention: Residual products left inside the device may damage the spraying device.
》》Drying time:
Usually 4 hours. After the concrete surface is completely dried, it can be put into use. Keep the concrete surface dry for the next 12 hours. If used for concrete curing, follow the dosage used on new concrete.
》》Maintenance period
Kentucky No.1 concrete protective agent in the United States has a curing effect on the concrete immediately after construction, and the internal reaction basically ends after 75 days. The concrete surface can be put into use after it has completely dried.
》》Construction method:
Spray American Kentucky1Apply concrete protective agent to the surface of the concrete and allow the entire surface of the concrete to be wettedCHEMTEC ONEMedium. Avoid forming small puddles on the surface of the concrete. If there are small puddles, use a brush to evenly sweep the excess product to a relatively dry area around it;Premature dry areas need to be repainted. ensureCHEMTEC ONEStaying on the surface of the polished concrete35-45Minute, then clean the surface residue with a rubber scraper and let it dry naturally.(For details, please refer to the construction manual)
Attention: If small water pits appear on the concrete surface due to uneven coating and are not cleaned in time, the natural drying consequence is that the product forms white crystals that are difficult to remove on the surface of the polished concrete.
》》Using tools:
Low pressure spraying equipment, brushes, rubber rollers, safety equipment, etc.
》》Shelf life and storage:
Shelf life of 2 years, storage temperature of 3-4 8 degrees Celsius. Do not freeze or condense the product! Products stored for a long time (more than 3 months) should be stirred evenly before use.
》》Attention:
Do not store in aluminum containers or use aluminum spray equipment. The product will react with aluminum to produce flammable hydrogen gas. For details, please refer toMSDS(Material Safety Test Form).
Do not spray or splash the product on glass, painted surfaces, or decorative surfaces to prevent contamination and damage to these surfaces.If the product splashes onto these surfaces, it must be immediately wiped with clean water. Ensure good ventilation. If necessary, dispose of waste appropriately in accordance with federal, state, or local environmental regulations.
》》Technical data and usage instructions:
If you need complete information, please checkMSDS(Material Safety Test Form)Technical data sheet orCHEMTEC ONEThe construction procedures for various specific surfaces can be viewed online on the US official website:Www.concretesealer.net
》》CHEMTEC ONE is capable of
Block the capillary pores in the concrete, effectively suppressing external pollutants from entering the concrete.
Improve the surface hardness and wear resistance of new and old concrete.
Improve the surface compressive strength of new and old concrete.
Reduce the penetration of chlorides.
● Inhibiting chemical erosion.
● React with free calcium lime in concrete to form a gel in its pores.
Delaying the peeling phenomenon on the surface of concrete.
● Enhance the compactness of concrete.
The surface of the pressed concrete will appear glossy after treatment, and the longer it is used, the better the glossiness.
》》CHEMTEC ONE cannot
●Optimize concrete.
Correct defects in concrete structures.
●Solve the corrosion prevention problem of concrete substrates.
●Sealing large cracks (only used to fill small cracks and shrinkage gaps)
●Completely prevent surface peeling of non aerated concrete caused by significant collapse or mortar peeling caused by fine layering of concrete surface due to poor quality construction.
●Fill the large pores formed by the high moisture content in the concrete before curing.